| WARNING Only licensed experts may install electrical components. They must adhere to local and state legislation and regulations. |
| WARNING Ground the product and verify outdoor installation grounding periodically. Failure to provide proper grounding can result in injury or death from electrical shock and can severely damage the equipment. |
| WARNING Do not operate in an explosive atmosphere, for example, when flammable gases or fumes are present. Operation of electrical equipment in such an environment constitutes a safety hazard. |
| CAUTION Do not damage or change the wiring. Incorrect wiring can cause damage and prevent or limit operation. |
The following figure shows the electronics inside the ENC652 enclosure. BOXALU‑US and BOXSS-US enclosures contain the same backplate and the same electronics.
- 1
- Radiation shield
- 2
- Enclosure ENC652
- 3
- AC (mains) input assembly
- 4
- 12 V backup battery
- 5
- Battery mounting clamp
- 6
- Wind lock
- 7
- Traffic sensor modules
- 8
- Device control relays
- 9
- Standard backplate
- 10
- DRI701
- 11
- Enclosure grounding rail for sensor cables
- 12
- DMU703
- 13
- Pressure port
- 14
- External ground connection
- 15
- Internal ground connection
- 16
- Rubber flanges
- 17
- FCC label
- 18
- Type label
- 19
- PMU701 grounding rail for sensor cables
- 20
- PMU701
- 21
- PTB110
- 22
- Cellular router
- 23
- AC/DC power supply
The following figure shows the electronics inside the ENC653 enclosure.
- 1
- Radiation shield
- 2
- Enclosure ENC653
- 3
- AC (mains) input assembly
- 4
- LED lights
- 5
- 12 V backup battery
- 6
- Battery mounting clamp
- 7
- Wind lock
- 8
- Traffic sensor modules
- 9
- Device control relays
- 10
- Standard backplate
- 11
- DRI701
- 12
- Enclosure grounding rail for sensor cables
- 13
- DMU703
- 14
- Pressure port
- 15
- External ground connection
- 16
- Internal ground connection
- 17
- Rubber flanges
- 18
- FCC label
- 19
- Type label
- 20
- PMU701 grounding rail for sensor cables
- 21
- PMU701
- 22
- Door switch
- 23
- PTB110
- 24
- Cellular router
- 25
- AC/DC power supply
The following figure shows the electronics inside the ENC722 enclosure.
- 1
- Enclosure ENC722
- 2
- AC (mains) input assembly
- 3
- AC/DC power supply
- 4
- 12 V backup battery
- 5
- Cellular router
- 6
- DMU703
- 7
- PMU701
- 8
- PMU701 grounding rail for sensor cables
- 9
- Slim backplate
- 10
- DRI701
- 11
- FCC label
- 12
- PTB110
- 13
- Type label
- 14
- Rubber flange
- 15
- External ground connection
- 16
- Pressure port
- 17
- Internal ground connection
For electrical installation, perform the following procedures in the order presented:
- Leading sensor cables to weather station enclosure
- Cutting sensor cables
- Adding wire-end ferrules
- Connecting sensor wires
- Connecting sensor cables
- Grounding sensor cables
- Inserting SIM card into IX20 cellular router
- Connecting multiband antenna
- Connecting fixed camera
- Connecting IR illuminator
- Connecting devices for device control
- Grounding weather station enclosure
- Overview of connecting power
- Finalizing installation
- Configuring the system
1 Internal cabling not shown
2 Internal cabling not shown
3 Internal cabling not shown